Send a Message

Contact Us

Company Address

Zhengzhou, China.

Aggregate crushing value test Step by Step Procedure

This test is repeated once or twice and the average crushing value of the aggregate is determined. The average crushing value in the different tests is the actual crushing value of aggregate. Important points to remember. It is recommended that the crushing value of aggregate should be less than 30%. If it is more than 30 % then 10% finer aggregate is suggested to use.

Aggregate Crushing Value Test Significance & Test

Significance of Aggregate Crushing Value Test Test precautions. The sample should be free from dust and other impurities. Wear safety gear while executing the test. Apparatus Required. Compression testing machine with gradually applying load capacity upto 40 tons. Preparation of Sample. The

Aggregate Crushing Value Test Determine Aggregate

17/05/2019 The ‘ aggregate crushing value test ` gives a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. Aggregate crushing value is defined as the percentage by weight of the crushed (or finer) material obtained when the test aggregates are subjected to a specified load under standardized conditions, and the strength of the aggregate

Aggregate Crushing Value Test -Determine Aggregate

05/05/2010 Aggregate crushing value = (W2 x 100) / (W1-W) W2 =Weight of fraction passing through the appropriate sieve. W1-W =Weight of surface dry sample. The mean of two result to nearest whole number is the aggregate crushing value. Result. The aggregate crushing value of the given sample= Aggregate Crushing Values for Roads and Pavement Construction

figure of aggregate crushing value test

The Purpose Of Aggregate Crushing Value Test. mobile jaw crusher pew jaw crusher raymond This study is a preliminary Figure 3: (a) Aggregate Crushing Value and . Get Price. Exp 4 Aggregate Impact Value Civil Engineers PK. Experiment to Determine the aggregate impact value of different coarse aggregate samples, (BS 812), Aggregate impact value test, plain & reinforced concrete . Get Price

Aggregate Crushing Value Calculator, Test on course and

Aggregate Crushing Value = W B W A ×100 W B W A × 100. Where, W A is weight of surface-dry sample. W B is weight of fraction passing the appropriate sieve. Reporting of Results. The mean of the two results shall be reported to the nearest whole number as the ‘aggregate crushing value’ of

METHOD B1 THE DETERMINATION OF THE AGGREGATE

The aggregate crushing value (ACV) of an aggregate is the mass of material, expressed as a percentage of the test sample. which is crushed finer than a 2,36 mm sieve when a sample of aggregate passing the 13,2 mm and retained on the 9,50 mm sieve is subjected to crushing under a gradually applied compressive load of 400 kN. 2 APPARATUS 2.1 An open-ended steel cylinder of

Aggregate impact and crushing test SlideShare

08/02/2012 (1) ARESULTSAn average is taken of the two tests and the result is recorded to the nearestwhole number as the Aggregate Impact Value.The AIV is normally about 105 per cent of the Aggregate Crushing Value and itcan be used for the same purpose.

Aggregate Crushing Value Testing Method YouTube

19/05/2017 Aggregate Crushing Value Testing Method YouTube. Aggregate Crushing Value Testing Method. Watch later. Share. Copy link. Info. Shopping. Tap to unmute. If playback doesn't begin shortly, try

Aggregate Crushing Value Calculator, Test on course and

Calculate Aggregate Crushing Value. The ratio of the weight of fines formed to the total sample weight in each test shall be expressed as a percentage, the result being recorded to the first decimal place: Aggregate Crushing Value = W B W A × 100. Where, W A is weight of surface-dry sample

Aggregate Crushing Value Test -Determine Aggregate

Procedure of Aggregate Crushing Value Test. Put the cylinder in position on the base plate and weigh it (W). Put the sample in 3 layers, each layer being subjected to 25 strokes using the tamping rod. Care being taken in the case of weak materials not to break the particles and weigh it (W1). Level the surface of aggregate carefully and insert the plunger so that it rests horizontally on the

(PDF) Aggregate Crushing Value Test busva gopal

Aggregate Crushing Value Test. Busva Gopal. Loading Preview. Download pdf × Close Log In. Log In with Facebook Log In with Google. Sign Up with Apple. or. Email: Password:

DETERMINATION OF AGGREGATE CRUSHING VALUE

The apparatus of the aggregate crushing value test as per IS: 2386 (Part IV) 1963 consists of: 1) A 15cm diameter open ended steel cylinder with plunger and base plate, of the general form and dimensions as shown in Fig 1. 2) A straight metal tamping rod of circular cross-section 16mm diameter and 45 to 60 cm long, rounded at one end. 3) A balance of capacity 3k, readable and accurate up

Aggregate impact and crushing test SlideShare

Impact, 10% Fines & Crushing TestsQuarry plant such as crushers, screens, conveyors, etc. are all subject to wearand these crushing tests can indicate the magnitude of the problem for designpurposes.PROCEDURE Aggregate Impact Value (SS 1974)1. The apparatus consists of a steel test mould with a falling hammer as shown in Figure 1. The hammer slides freely between vertical

Aggregate Crushing Value Test yogaingreifswald.de

Aggregate Crushing Value Test Procedure. Aggregate crushing value test procedure procedure step 1 first the aggregate sample sieve through 125mm sieve and collect it which is retained in 10 mm sieve step 2 now the sample should be dried through the oven up to 4 hours at 100 deg to 110 deg step 3 then the aggregate sample should be filled in the metal cup by 3 layers each layer should be tamped

Aggregate Crushing Value and 10% Fines Value.pdf

Chapter 7 Standard Test Procedures Tests For Aggregates And Bricks MAY 2001 Page 7.35 7.7.1.9 Results. Calculate the mean of the two values determined to the nearest whole number. Report the mean as the Aggregate Crushing Value, unless the individual results differ by more than 0.07 times the mean value. In this case repeat the test on two further specimens, calculate the median of the four

What is the Crushing value of Aggregates..?? Firstalert.in

27/05/2020 The crushing value of an aggregate indicates its resistance against crushing under gradually applied compressive loads. The standard aggregate crushing test is made on aggregate passing 12.5mm IS sieve and retained on 10 mm IS sieve. Procedure. About 6.5 Kg material consisting of aggregates passing 12.5mm IS sieve and retained on 10mm sieve is taken the aggregate in a

Aggregate Impact Value Test, Procedure, Result &

Therefore, aggregate used for such propose should have sufficient toughness to resist their disintegration due to the impact. This important property of aggregate is determined by the aggregate impact value test. This resistance of aggregate may differ from resistance to gradual load which we measure in the crushing value test.

Abrasion Test On Aggregate (Los Angeles Abrasion Test)

Abrasion Test is the measure of aggregate toughness and abrasion resistance such as crushing, degradation and disintegration. This test is suggested by AASHTO T 96 or ASTM C 131: Resistance to Degradation of Small-Size Coarse Aggregate by Abrasion and Impact in Los Angeles Machine.

Aggregate Crushing Value Test -Determine Aggregate

Aggregate Crushing Value Test Apparatus. A steel cylinder 15 cm diameter with plunger and base plate. A straight metal tamping rod 16mm diameter and Sampling of Aggregates. Coarse aggregate passing 12.5mm IS sieve and retained on a10mm IS sieve are selected and heated Calculation of Aggregate

Aggregate crushing value test Step by Step Procedure

Aggregate crushing value test is done the find the actual crushing value of aggregate. We Need to carry out this test, 1.To find out how much resistance does the aggregate has against the surface abrasion under traffic. 2.To find out how much resistance does the aggregate can withstand under the roller during construction. 3.To determine the strength of coarse aggregate and suitability of the

(PDF) Aggregate Crushing Value Test busva gopal

Aggregate Crushing Value Test. Busva Gopal. Loading Preview. Download pdf × Close Log In. Log In with Facebook Log In with Google. Sign Up with Apple. or. Email: Password:

DETERMINATION OF AGGREGATE CRUSHING VALUE

The apparatus of the aggregate crushing value test as per IS: 2386 (Part IV) 1963 consists of: 1) A 15cm diameter open ended steel cylinder with plunger and base plate, of the general form and dimensions as shown in Fig 1. 2) A straight metal tamping rod of circular cross-section 16mm diameter and 45 to 60 cm long, rounded at one end. 3) A balance of capacity 3k, readable and accurate up

Aggregate Crushing Value Civil Engineering

AGGREGATE CRUSHING VALUE This test helps to determine the aggregate crushing value of coarse aggregates as per IS: 2386 (Part IV) 1963. The apparatus used is Cylindrical measure and plunger, Compression testing machine, IS Sieves of sizes 12.5mm, 10mm and 2.36mm. Procedure to determine Aggregate Crushing Value i) The aggregates passing through 12.5mm and retained on

Aggregate Crushing Value Test yogaingreifswald.de

Aggregate Crushing Value Test Procedure. Aggregate crushing value test procedure procedure step 1 first the aggregate sample sieve through 125mm sieve and collect it which is retained in 10 mm sieve step 2 now the sample should be dried through the oven up to 4 hours at 100 deg to 110 deg step 3 then the aggregate sample should be filled in the metal cup by 3 layers each layer should be tamped

Aggregate Crushing Value and 10% Fines Value.pdf

Chapter 7 Standard Test Procedures Tests For Aggregates And Bricks MAY 2001 Page 7.35 7.7.1.9 Results. Calculate the mean of the two values determined to the nearest whole number. Report the mean as the Aggregate Crushing Value, unless the individual results differ by more than 0.07 times the mean value. In this case repeat the test on two further specimens, calculate the median of the four

What is the Crushing value of Aggregates..?? Firstalert.in

27/05/2020 The crushing value of an aggregate indicates its resistance against crushing under gradually applied compressive loads. The standard aggregate crushing test is made on aggregate passing 12.5mm IS sieve and retained on 10 mm IS sieve. Procedure. About 6.5 Kg material consisting of aggregates passing 12.5mm IS sieve and retained on 10mm sieve is taken the aggregate in a

Introduction on aggregate crushing value apparatus

(vi) Two tests should be conducted. 7. CALCULATION: • Aggregate crushing value = B/A x 100% • The result should be recorded to the first decimal place and the mean of the two results reported. • To achieve a high quality of pavement, aggregate possessing low crushing value should be preferred. 8.

Stone Aggregate Testing Laboratory Sigmatest

The Aggregate Crushing Value offers a related measure of the resistance of an average to crushing under a compressive load that is gradually applied. Test Method: IS: 9376-1979, IS: 2386 (P-4)1963. Drying Shrinkage: Drying shrinkage is defined as the contracting of a hardened concrete mixture due to the loss of capillary water. This shrinkage causes an increase in tensile stress, which may